Incompatibility —Too Many Good Things?

The wide variety of materials options and mix proportions possible in concrete allows it to be customized for a wide range of applications and placement and service environments. However, the cementitious materials (cements, fly ashes, slag cements, etc.) and chemical admixtures (accelerators, retarders, water reducers, etc.) are all chemically complex and this complexity can lead to problems when they don’t work together properly. Even when all materials meet and exceed their specification requirements individually, problems can arise under field conditions. These problems might manifest themselves as:

• Early stiffening or excessive retardation (which can lead to workability, placeability, consolidation, and finishing issues)
• Early-age cracking (including plastic shrinkage and possibly the ability to attribute the cause of cracking to chemical, physical, and environmental phenomena)
• Air-void system issues (including non-uniformity, low air contents, coalescence of air voids around aggregate, and excessively large voids)

Although these problems are relatively rare, the resulting construction delays, performance issues, and loss of confidence in concrete as the preferred construction material are unacceptable. FHWA and PCA co-sponsored research into these phenomena, with the goal of minimizing or preventing these problems in the field. The project developed relatively simple protocols for evaluating concrete material combinations both pre-construction and during construction.

Preconstruction

The pre-construction protocol is suited for testing of new mix designs and evaluating new materials sources. Tests should be performed over the range of temperatures expected in the field and cover the range of mix proportions expected to be used.

Figure 1, from the FHWA TechBrief (see complete reference below), summarizes the pre-construction protocol. The protocol begins with a review of material characteristics that have been implicated in incompatibility issues, for example, cementitious materials fineness and alkali contents. A review of historical properties of the materials being used is valuable as changes in some characteristics can raise a flag that might cause the concrete producer to be wary. Additional testing is suggested to bracket potential problems, for example, some incompatibility issues only appear with certain materials during hot weather. Potential solutions are also recommended in the pre-construction protocol, and testing can confirm which of these solutions will be effective. This allows the problems to be avoided or permits changes to be quickly implemented if problems arise during construction.

Figure 1. Summary of pre-construction protocol. Source: FHWA TechBrief

During Construction

A separate testing protocol has also been developed for use during construction and it is best suited to identifying issues that arise during construction. The goal of these tests is to assure that materials used are similar to those used in pre-construction testing. Figure 2 suggests routine tests during construction that can be used to monitor performance, and quickly detect potential problems as they arise, allowing a more rapid response, particularly if various solutions have been evaluated with pre-construction testing.

Figure 2. Summary of protocol for use during construction. Source: FHWA Tech Brief

It is important to note that the protocol offers flexibility because not all of these tests are routinely available. Some are relatively more time consuming or costly to run. The decision about which suite of tests to use will be based on engineering judgment based on the costs/benefits and project-specific risks. A high-profile bridge project will obviously require more tests than a neighborhood sidewalk.

Related resources:

• TechBrief: Protocol to Identify Incompatible Combinations of Concrete Materials, FHWA-HRT-06-082, Federal Highway Administration, Turner-Fairbank Highway Research Center, Maclean, Virginia, USA, July 2006, 4 pages.

• Taylor, P.C.; Johansen, V.C.; Graf, L.A.; Kozikowski, R.L.; Zemajtis, J.Z.; and Ferraris, C.F., Identifying Incompatible Combinations of Concrete Materials: Volume I–Final Report, FHWA HRT-06-079, Federal Highway Administration, Turner-Fairbank Highway Research Center, Maclean, Virginia, USA, August 2006, 162 pages.

• Taylor, P.C.; Johansen, V.C.; Graf, L.A.; Kozikowski, R.L.; Zemajtis, J.Z.; and Ferraris, C.F., Identifying Incompatible Combinations of Concrete Materials: Volume II–Test Protocol, FHWA HRT-06-080, Federal Highway Administration, Turner-Fairbank Highway Research Center, Maclean, Virginia, USA, August 2006, 86 pages.

• Taylor, P.C.; Johansen, V.C.; Graf, L.A.; Kozikowski, R.L.; Zemajtis, J.Z.; and Ferraris, C.F., Identifying Incompatible Combinations of Concrete Materials: Volume III—Additional Appendices, R&D SN2897c, Portland Cement Association, Skokie, Illinois, USA, 2008, 89 pages.

 
Careers | Sitemap | Disclaimer | Privacy Policy | © 2009 Portland Cement Association - All Rights Reserved